They are making a number of great points relating to How to Install a Bathtub Yourself as a whole in the article below.
Setting up a tub isn't precisely rocket science, however it does call for strong plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is readily accessible, the job can relocate quickly; if you need to open up a wall to remove the old tub and also place the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub as well as embeded in the new one. See to it you have actually certified yourself for the task and also are comfortable attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Possibilities are you might need a professional plumber to make tube links.
This post will aid you install a brand-new bathtub in your shower room if you have already purchased a brand-new tub and do not require to transform the plan of your previous water system pipelines.
Your devices and product list ought to consist of the following:
Getting ready for the Installation
Firstly, the supporting frame provided with the bath ought to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps system to avoid pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its final position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite problematic as a result of the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Before moving on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the water supply and also examine all joints as well as new pipework for leakages as well as tighten them if required. Fill the bathtub as well as also inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the tub must wait up until the bath tub has been used a minimum of once as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Safeguard the faucet in position with the producer given backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to pass through the wall between the bath and also the tiling, resulting in problems with wetness as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes as well as cartridges, and also can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill up the tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can crack relatively very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very occupied with How to Install a Bathtub Yourself and I'm hoping you liked the new piece. Do you know another person who is sincerely interested in the niche? Why not share it. I treasure reading our article about How to Install a Bathtub Yourself.
Get A Free Estimate